DIGITAL PHOTO/CONTACT TACHOMETER This PHOTO/CONTACT TACHOMETER is small in size, light in weight, easy to carry. Although complex and advanced, it is convenient to use and operate. Its ruggedness will allow many years of use if proper operating techniques are followed. Please read the following instructions carefully and always keep this manual within easy reach. ¡¡ 1. FEATURES * Multifunctional, one instrument combines PHOTO TACH. (RPM) & CONTACT TACH. (RPM , m/min., ft/min). * Wide measuring range. * The last Value / max. Value / min. Value will be automatically stored in memory and can be obtained by pressing MEMORY CALL BUTTON . * LCD display gives exact rpm with no guessing or errors and saves battery energy. * This tachometer used the exclusive one chip of MICROCOMPUTER LSI-circuit and crystal time base to accurately offer the high accuracy measurement. 2. SPECIFICATIONS Display : 5 digits, 10mm (0.4 ) LCD ( Liquid Crystal Display) Measurement range : PHOTO TACH.: 2.5~99,999 RPM CONTACT TACH. : 2.5~19,999 RPM SURFACE SPEED: 0.05~1,999.9 (m/min.) 0.2~6,560 ft/min Resolution: TACHOMETER: 0.1 RPM (2.5 ~ 999.9 RPM) 1 RPM (over 1,000 RPM) SURFACE SPEED: 0.01m/min. (over 10 m/min.) 0.1 m/min. (over 100 m/min.) 0.1 ft/min. (0.1 ~ 999.9 ft/min.) 1 ft/min. (over 1,000 ft/min.) Accuracy : TACH.: (0.05%+1 RPM) SURFACE SPEED: (0.05%+0.03m/min.) Sampling Time: PHOTO TACH. (1 sec. over 60 RPM). CONTACT TACH. (1 sec. over 15 RPM) Photo Tach. Detecting distance : 50 to 150mm / 2 to 6 inch. (typical max. 300mm/12 inch ). Test range select: Automation Battery : 4x1.5AA(UM-3)battery Operation temp. : 0-50 (32-122 ) Size : 215x65x38mm (8.5 x2.6x1.5 inch) Weight : 300g/0.651b (including batteries) Accessories : Carrying case ...............................1pc. Reflective tape marks (350mm).......2pc. RPM adapter (CONE).....................1pc. RPM adapter (FUNNEL).................1pc. Surface speed test wheel.................1pc. Operation manual...........................1pc. 3-8 Rotating ring 3-9 Circumferential speed ring 3-10 Battery Compartment/Cover 4. PHOTO TACH. MEASURING PROCEDURE 4-1. Slide the FUNCTION SWITCH to RPM PHOTO position. 4-2. Apply a reflective mark to the object being measured. Depress the MEASURE BUTTON and align the visible light beam with the applied target. Verify that the MONITOR INDICATOR lights when the target passes thru the light beam. Release the MEASURE BUTTON when the reading stabilizes (about 2 seconds). If the test RPM less than 50 RPM, suggest to attach more REFLECTIVE MARKS averagely. Then divided the reading shown by the number of REFLECTIVE MARKS is the real RPM to get high resolution & stability on display reading. 4-3 REFLECTIVE MARK Cut and peel adhesive tape provided into approx. 12mm ( 0.5 ) sq uares an d ap ply on e square to each rotation shaft. a. The non-reflective area must always be greater than the reflective area. b. If the shaft is normally reflective, it must be covered with black tape or black paint before attaching reflective tape. 5.CONTACT TACH. MEASURING PROCEDURE 5-1 Slide the FUNCTION SWITCH to RPM CONTACT position. 5-2 Depress the MEASURE BUTTON and lightly pressing the rotating ring (3-8) against the center hole on the rotating hole. Release the MEASURE BUTTON when the reading stabilizes (approx. 2 seconds ). 6. SURFACE SPEED MEASUREMENT 6-1Slide the FUNCTION SWITCH to m/min (SURFACE SPEED) or ft/min. (SURFACE SPEED) position. 6-2Depress the MEASURE BUTTON and simply attaching the surface speed test wheel to the detector. Release the MEASURE BUTTON when the reading stabilizes. 7. MEMORY CALL BUTTON OPERATION 7-1 A readout (the last Value, max. Value, min. Value) obtained immediately before releasing the MEASURE BUTTON is automatically memorized. For example, please ref. fig. 2. 7-2 That memorized values can be displayed on the indicator when A. First push-To display the last value: LA and the last value will be displayed by turn. B. Second push-To display the maximum value: UP and the max. value will be displayed by turn. C. Third push-To display the minimum value: dn and the min. value will be displayed by turn. 8. BATTERY REPLACEMENT 8-1 When it is necessary to replace the battery (battery voltage less than approx. 5V ), symbol - + will appear on the display. 8-2 To loose the screw of the battery cover (Fig.1, 3- 10) away from the instrument and remove the batteries. 8-3 Install the batteries correctly into the case. Permanent damage to the circuit from incorrect installation. 8-4 If the instrument is not to be used for any extended period, remove batteries. ¡¡ |